Crystal Resin for Flowers FLOWERA 100-72-550 Low Viscosity UV++
Code: 30388
Related products
Product detailed description
Crystal Resin FLOWERA 100-72-550 UV++ – for dried flowers and beetles
FLOWERA 100-72-550 UV++ is a thin, crystal-clear epoxy resin designed for embedding dried flowers, beetles and other small botanical material. Thanks to its low viscosity, it penetrates details excellently and creates a smooth, highly glossy surface after curing.
Advantages
- Ultra clear, high resistance to yellowing (UV++)
- Very good self-degassing
- Thin – perfectly coats fine details
- Long working time – comfortable, stress-free work
- Perfectly glossy surface after pouring and curing
Suitable applications
- Casting height: up to 100 mm
- Material: dried flowers (dry matter), beetles, insects, other botanical objects
Recommended moulds
- Silicone Moulds – Small Decorations: spheres, cubes, smaller 3D shapes, pyramids, crystals, paperweights
- Silicone moulds – large decorations: large spheres and cubes, larger 3D shapes, pyramids, large letters and numbers
Properties and Technical Parameters
| Type | Two-component epoxy resin (A – resin / B – hardener) |
| UV stability | UV stable ++ |
| Clarity | Ultra Clear |
| Viscosity after mixing A+B | 550 mPa·s (indicative scale: 300 mPa·s = extra low viscosity → 9000 mPa·s = extra high viscosity) |
| Mixing ratio (by weight) | 2 : 1 (A : B) |
| Mixed volume at once | up to 20 l |
| Max. layer height | up to 100 mm |
| Processing time | approx. 18 hours |
| Curing time | approx. 72 hours (depending on temperature and material quantity) |
| Processing temperature | ideally 22–23 °C (do not drop below 20 °C) |
| Hardness after curing | 85 Shore D (for comparison: 56 Shore D = medium hardness, 90 Shore D = very hard) |
| Finishing | sanding and polishing |
Pigmentation and Colouring
For transparent colouring, use resin dyes designed for epoxies.
Packaging
- 1.4 kg (total of components A + B)
- 0.7 kg (total of components A + B)
Usage notes
- When pouring porous materials, first seal the surface with a sealant to prevent bubbles from being released during curing.
- The processing temperature (mixing, casting) must not fall below 20 °C.
- During curing, do not expose castings to temperature fluctuations – they negatively affect the appearance of the surface.
- The mixing ratio is by weight. Therefore, always weigh both components (volume measurement is not recommended).
Safety and classification
The mixture is classified as hazardous according to (EC) No. 1272/2008.
Component A
Standard hazard statements:
H315 Causes skin irritation.
H317 May cause an allergic skin reaction.
H319 Causes serious eye irritation.
H411 Toxic to aquatic life with long lasting effects.
Precautionary statements:
P101 If medical advice is needed, have product container or label at hand.
P102 Keep out of reach of children.
P264 Wash hands and affected body parts thoroughly after handling.
P273 Avoid release to the environment.
P280 Wear protective gloves.
P333+P313 If skin irritation or rash occurs: Get medical advice/attention.
P337+P313 If eye irritation persists: Get medical advice/attention.
Component B
Standard hazard statements:
H302 Harmful if swallowed.
H314 Causes severe skin burns and eye damage.
H317 May cause an allergic skin reaction.
H318 Causes serious eye damage.
H412 Harmful to aquatic life with long lasting effects.
H302+H332 Harmful if swallowed or if inhaled.
Precautionary statements:
P101 If medical advice is needed, have product container or label at hand.
P102 Keep out of reach of children.
P261 Avoid breathing dust/fume/gas/mist/vapours/spray.
P273 Avoid release to the environment.
P280 Wear protective gloves/protective clothing/eye protection/face protection.
P303+P361+P353 IF ON SKIN (or hair): Take off immediately all contaminated clothing. Rinse skin with water or shower.
P303+P361+P353 IF ON SKIN (or hair): Take off immediately all contaminated clothing. Rinse skin with water/shower. Rinse skin with water or shower.
P305+P351+P338 IF IN EYES: Rinse cautiously with water for several minutes. Remove contact lenses, if present and easy to do. Continue rinsing. Continue rinsing.
P310 Immediately call a doctor.
P501 Dispose of contents/container to an authorised waste disposal plant or return to supplier.
Additional parameters
| Category: | Resin for Dried Flowers and Bugs |
|---|---|
| Usage: | Decoration, Beetles, Keychains, Flowers |
| Volume: | 1kg |
| Product type: | Casting resin |
| Max. casting layer: | 100mm |
| Curing time: | 72h |
| ? Density mPA.s: | 1200 |
| ? Mixed volume at once: | 10L |
Be the first who will post an article to this item!
Be the first who will post an article to this item!
E-Shop Obchodprobydleni.cz focuses on selling casting resin from a Czech manufacturer under the PourArt brand. PourArt casting resin is designed for the production of furniture from resin, jewellery from resin, various decorations from resin and pictures from resin. We supplement the range of casting resin with other accessories for epoxy resin products. We focus on decorations for casting resin, resin grinding and polishing, resin moulds and other necessary tools and materials for working with casting resin.